Ang release bearing ng internal combustion forklift clutch ay gumagana nang napakadalas, at ang dalas ng pinsala nito ay nagdudulot ng malaking proporsyon ng mga pagkabigo ng forklift. Kung ang driver ay nagpapatakbo ng maayos at inaalagaan ito nang maayos sa isang napapanahong paraan, maaari itong magamit nang humigit-kumulang 3 buwan. Gayunpaman, sa panahon ng medium maintenance, kinakailangan ding palitan ito. Kung mababa ang technical level ng driver, halos buwan-buwan ay nasira ang release bearing ng forklift na kanilang minamaneho, at masisira rin ang iba pang bahagi gaya ng release lever at clutch plate.
Ano ang mga dahilan kung bakit ang clutch release bearings ay madaling masira? Sa praktikal na karanasan, kahit na ang mga driver ay mahigpit na kinakailangan na tumulo ng langis sa separation bearing isang beses sa isang araw, ito ay hindi lamang masalimuot na operasyon, kundi pati na rin ang madalas na pinsala sa tindig.
After analysis, it is believed that due to the high temperature transmitted by the engine to the separation bearing, coupled with the high temperature generated by the high-speed rotation of the bearing, it is difficult for lubricating oil to remain in the bearing. The bearing operates continuously at high temperatures, and due to poor lubrication conditions, the separation bearing is prone to frequent damage.
According to the above problems, we have also tried to put the bearing in the grease Negage, so that the grease can be soaked into the bearing. After this treatment, the grease can fill the bearing, but its performance is greatly reduced due to the structural damage of the grease after high-temperature treatment. The effect of using this method is not ideal, and the service life of the bearing has not been extended. The release bearing was also directly greased with a pointed Grease gun.
After installation and inspection, the service life of the bearing has been greatly extended. This oil injection method has achieved satisfactory results, but the operation is relatively complex. Then we explored how to add butter when the engine was in doubt. First, the 475C engine was successfully tested, and then the 475C and 480492 engines were tested with good results. After repeated practice, improvement, and summary of experience, Z has finally developed a relatively simple oil injection operation method. The specific process is as follows:
1. Oil injection method for engine suspect body
First, open the clutch cover and observe the wear of the release bearing. If it is confirmed that the bearing is not damaged or the wear does not exceed the limit, remove the clutch pedal, adjust the connecting rod shaft pin to return the release bearing and its seat to the position behind Z, use a pointed nozzle Grease gun to fill the hole of the bearing seat with grease until there is oil overflow from the bearing, then slightly rotate the bearing, fill again, and repeat the above work until there is a little grease overflow around the bearing, Rotate the bearing again, observe the amount of oil, and if there is resistance to rotation, it indicates that the bearing is filled with butter. Then remove a small amount of grease that has leaked from the release bearing seat, and reassemble the removed pins and clutch covers.
2. Oil injection method for engine disassembly
Disassemble the engine to expose the assembly parts of the release bearing and the bearing seat, and use a pointed Grease gun to fill the small oil hole below the inner ring of the release bearing seat. If there is grease overflowing from the bearing, rotate the bearing until there is grease overflowing from every ring of the bearing.
After the above two methods of disposal, the separation bearing can no longer be refueled within six months.
More about VAFEM Maintenance-free Bearings：
Agricultural machinery requires better seals for contaminated conditions, provisions for misalignment, and economical mountings for shafts and housings. VAFEM offers bearings for disc harrows, planters, mowers, rakes, all types of balers, tillage, seeding and forage harvester equipment, combines, cotton pickers/stripers, and other agricultural equipment like silo unloaders and grain elevators.
We also offer a complete line of insert ball bearings, shaft mounted with either tapered adapters or locking collar or set screws. Our proven seal designs include low torque shields to heavy-duty triple lip seals. Disc harrow bearings are also available with either round, square, or hexagonal bores. All bearings are available with or without re-lubrication holes.
https://www.vafem.com/products/Agricultural-Bearings/775.html
2023-08-03