Abstract: Sa pag-unlad ng panlipunang ekonomiya, ang industriya ng transportasyon ng Tsina ay mabilis na umunlad, at ang konstruksyon ng inhinyero ng tren ay gumawa din ng malaking pag-unlad. Ang papel na ito ay tumatalakay sa mga karaniwang pagkakamali at kontra-hakbang ng mga rolling bearings para sa railway freight cars, umaasa na mapabuti ang mga benepisyong pang-ekonomiya at kaligtasan ng operasyon ng railway transport.
Mga pangunahing salita: rolling bearing; Mga karaniwang pagkakamali; Countermeasures
pagpapakilala ko
Ang pagtaas ng hanay ng aplikasyon ng mga railway freight car ay higit na nagpabuti sa kalidad ng paggamit ng mga railway freight cars at nagpapataas ng kaligtasan ng mga freight car. Ang paggamit ng rolling bearing ay gumaganap ng isang mahalagang papel sa pagpapatakbo ng sasakyan. Samakatuwid, partikular na mahalaga na magsagawa ng mga hakbang sa proteksyon nang maaga. Kapag nangyari ang isang pagkakamali, ang pinsala at kahihinatnan nito ay napakaseryoso.
1. Maikling panimula ng proseso ng pag-mount ng pindutin
Ang pangunahing proseso ng pag-mount ng bearing press ay upang sukatin ang diameter ng bearing inner race at axle journal ayon sa pagkakabanggit pagkatapos na ang bearing at wheel set ay nasa parehong temperatura, piliin at pagsamahin ang mga ito ayon sa isang tiyak na halaga ng interference, at pagkatapos ay gumamit ng CNC hydraulic equipment na may awtomatikong pag-record ng curve function upang pindutin ang tindig papunta sa journal ng gulong itinakda sa pamamagitan ng malamig na pagpindot, at hawakan ang presyon para sa isang tiyak na oras upang gawin ang tindig pindutin sa lugar. Sa proseso ng bearing press fitting, ang dalawang panloob na singsing ng bearing ay pinindot sa journal, at ang press fitting na kagamitan ay awtomatikong nagtatala ng stroke at presyon ng hydraulic cylinder. May mga pagkakaiba-iba sa istraktura ng iba't ibang uri ng mga bearings, ngunit ang proseso ng press fitting at press fitting curve recording principle ay pareho.
2 Pagsusuri ng sanhi ng kasalanan
Ang mga rolling stock bearings ng tren ay kadalasang ginagamit sa mga lokomotibo at rolling stock. Kasama sa bearing structure ng rolling stock ang traction motor bearing, axle box bearing, transmission system bearing, power equipment bearing at cooling system bearing, atbp., at ang axle box bearing ng rolling stock ang pangunahing bearing. Ang maikling cylindrical roller bearings ay kadalasang ginagamit sa mga pampasaherong sasakyan. Ang tapered roller bearings ay kadalasang mga truck bearings. Ang uri, layout at function ng mga bearings ng sasakyan ay katulad ng mga bearings ng locomotive axle box.
2.1 Abnormal na tunog
Ang tunog ng rolling bearing sa mabuting kondisyon ay tuloy-tuloy at presko sa panahon ng mabilis na pag-ikot, at walang abnormal na sound jamming sa paulit-ulit na pag-ikot. Gayunpaman, kung ang tindig ay hindi nababaluktot sa panahon ng pag-ikot at sinamahan ng tunog ng rolling body breaking, ito ay nagpapahiwatig na ang rolling bearing ay may malubhang kasalanan.
2.2 Maluwag na bearing sealing cover
Ang takip ng selyo ay karaniwang hindi pinapalitan ng mga bagong produkto sa oras sa panahon ng pagpapanatili, na nagreresulta sa ang takip ng selyo ay hindi naibalik sa oras pagkatapos ng paghugis, at ang bibig ng panlabas na singsing ay kadalasang umaangkop sa takip ng selyo, na magiging sanhi ng pagluwag. Gayunpaman, ang alitan sa pagitan ng upuan ng selyo at ang singsing ng selyo ay tumataas pagkatapos tumaas ang bilis, at ang takip ng selyo ay hinihimok na umikot nang magkasama, na nagreresulta sa pagkaluwag ng takip ng selyo. Sa panahon ng inspeksyon ng tren, kinakailangan lamang na hawakan ang pagtanggal ng takip ng selyo. Sa wakas, ang pagkaluwag ng takip ng sealing ay pinalubha nang walang paggamot.
2.3 Tonnage skip ng press fitting curve
The quality of bearing press-fitting has a direct impact on the safe operation of vehicles. In actual production, it is very common that the displacement-pressure curve jumps at the initial stage of bearing press installation. Although the technical standard does not clearly specify the limit of the weight jump of the bearing press fitting curve, and the analysis shows that the weight jump of the displacement-pressure curve at the initial stage has no impact on the subsequent use of the axle, the product inspection usually determines that the weight jump exceeds 58.8KN (the minimum qualified press fitting force) as the curve abnormality, and the bearing needs to be removed, re-selected and pressed.
2.4 Increased cage breakage
Because the strength of the cage itself is not very high and the processing and manufacturing level is also low, manufacturing defects exist in the cage. Due to insufficient strength, the cage can not meet the needs of railway speed increase and heavy load. The stress of the cage is restricted by the quality of the wheel set tread, so the stress degree of the cage is greatly reduced. It can be seen that the damage to the bearing cage is the tread failure. The harm to the cage will gradually increase with the increase of train speed. The reason is that the impact force depends on the speed of the train, and the impact frequency increases with the increase of the train speed. The harm to bearings is also increasing. Finally, the reason for the cage breakage is that the pressure is too large, the sealing of the seal cover is reduced, and the outside is loose. The grease is thrown out in a large amount during the train operation, and the lubrication effect is gradually lost.
2.5 Loose bolts at shaft end
During the technical maintenance of the train, the train inspector shall check the locking of the axle end bolts and the connecting axle end bolts respectively. If the locking is broken or lost during the inspection, the axle end bolts shall be checked immediately. If the axle end bolts are found to be loose or loose, the axle end bolts shall be immediately removed and replaced.
2.6 Others
In addition, incorrect assembly and use may cause deformation of the cage, increase the friction between the cage and the rolling body, make it stick to the rolling body, and increase the friction between the cage and the inner and outer rings. The vibration and noise are further increased, resulting in bearing damage and failure.
3. Condition monitoring technology of rolling bearing
① Vibration signal analysis and diagnosis method. One of the most widely used methods in the monitoring and diagnosis of rolling bearings is the vibration signal analysis and diagnosis method. When the surface of rolling bearing is partially damaged, the bearing will generate periodic broadband pulse excitation signal. The spectrum structure of rolling bearing vibration can be divided into three types. (1) Low frequency spectrum (lower than 1kHz), including fault characteristic frequency of bearing and vibration characteristic frequency caused by machining error. The corresponding fault of the bearing can be diagnosed by analyzing the spectrum line of the low frequency band. (2) Medium frequency spectrum (1~20kHz), the natural vibration frequency of bearing caused by bearing surface damage. Generally, resonance regulation technology is used to obtain vibration signals with high signal to noise ratio, so as to carry out bearing fault analysis. (3) High frequency spectrum (more than 20kHZ) refers to the frequency energy distribution of the bearing damage impact exceeding 20kHZ, mainly including the high frequency part of the signal containing more than 20kHZ. High-frequency signal analysis is usually used as the most common method to diagnose the initial bearing fault. ② Monitoring and diagnosis method of bearing lubrication condition. When the lubrication state of the bearing rolling surface changes, such as from full liquid lubrication? When it comes to dry friction, the direct contact time between metals will continue to increase, the impulse value of bearing will also increase correspondingly, and the oil film resistance will continue to decrease. Therefore, oil film resistance diagnosis method and oil film thickness method are two commonly used methods in monitoring work. ③ Temperature monitoring diagnosis method. As a rotating part, the rolling bearing will generate heat when working. When the bearing is damaged, the bearing temperature will change. Therefore, the bearing temperature monitoring method can be used to diagnose the bearing fault. However, when the bearing temperature is obvious, the fault often has reached a very serious level, so this method is mainly used to assist monitoring and diagnosis methods to ensure that important equipment will not be scrapped.
4 Improvement measures and suggestions
4.1 Measures to avoid weight jump of bearing press fitting curve
(1) It is recommended that the axle design unit improve the axle drawing and increase the length of the axle lead-in section. Effectively improve the fitting relationship between the bearing press fitting and the timing, reduce the press fitting resistance, and have no effect on the effective joint surface of the bearing and the journal, and have little impact on the strength of the axle. (2) When machining the axle, the length of the lead-in section is controlled according to the upper limit of the size, which can effectively increase the included angle between the conical surface busbar of the bearing inner ring and the busbar of the axle lead-in section, and reduce the press-fitting resistance of the bearing and the axle alignment. (3) When machining the inner diameter of the bearing, the transition arc between the inner diameter and the conical surface is controlled as small as possible to reduce the contact area between the bearing inner race and the journal entry section, which can effectively reduce the pressure mounting resistance of the bearing and the axle alignment. (4) Before pressing the bearing, when servicing the axle, check the processing quality of the transition part at the rear of the journal entry section one by one. If the transition is not smooth, use abrasive cloth to polish it first to facilitate the smooth alignment of the bearing with the axle. (5) To improve the processing parameters of axle form grinding, the transition part at the rear of the journal entry section can be changed to form grinding machine, and the arc radius of the transition part can be appropriately increased, so as to increase the included angle between the cone generatrix of the bearing inner ring and the generatrix of the axle entry section, and reduce the resistance force of the bearing and the axle alignment. (3) Strengthen the status inspection of the bearing press-fitting equipment and conduct regular inspection on the diameter of the guide sleeve. On the premise of ensuring the smooth installation and withdrawal of the bearing, the larger the diameter of the guide sleeve is, the more conducive to the smooth alignment of the bearing.
4.2 Sealing cover
When the workers repair or overhaul the vehicle, the interference of the outer ring and seal ring shall be calculated from the interference of the outer ring and seal cover.
4.3 Bearing cage
The manufacturer must improve the technological level. The quality inspection department shall carry out quality supervision and strict control. Strengthen supervision awareness and eliminate manufacturing defects of products. The rigid cage should be replaced with plastic cage. It should adapt to the development of new materials for vehicle speed increase in the future, and the quality of cage should be improved. Strengthen the inspection and repair of wheel sets at all levels, ensure the quality of wheel sets, especially wheel tread, and avoid the impact and damage of tread defects on bearings.
Conclusion
To sum up, it is necessary to be familiar with the fault form and fault development stage of rolling bearing. To master the analysis principle and method of rolling bearing fault diagnosis is the premise of accurate diagnosis of rolling bearing fault.
More about VAFEM pulley and tensioner bearings:
VAFEM Tensioner pulleys provide precise guidance and constant belt tension in the belt drive. They can either be mounted rigidly or combined with the tensioning elements to belt tensioners. Tensioner pulleys increase the wrap angle on belt drives and thereby transmit higher performance. They enable a change in the rotational direction of the connected aggregates. In combination with belt tensioners, they also compensate for operational belt stretching.
Various materials are used in the production of belt tensioners, depending on the technical requirements, for example deep-drawn sheet steel, turned bar, cast steel or Polyamide 66 with glass fibre content. VAFEM Tensioner pulleys Spare Parts brand are designed for a maximum temperature of up to 120°C and 6 000 RPM.
The precision-machined contact surfaces of the belt tensioner ensure optimal installation of the drive belt, low wear and minimal operating noise.
Construction of tensioner pulleys
1.Pulley
2.Cover plate
3.Sleeve
4.Ball bearing
5.Seal ring
2023-03-15